Ruger mkII or charger integral supressor

[jongo1]

can anybody give me a ballpark figure on what it would cost me to integrally supress my mkII or charger,And who would be best in the area to do it?

 

[VUPDblue]

You can go with the Oasis suppressed top end for the MKII or MKIII. It runs $695 plus the $200 stamp. You're looking at ~$900 for the top end to add to your existing gun. You don't really need anyone to do the work if you go with something like the oasis. It's as simple as swapping out your old top end and installing the oasis.

Linky: Gemtech OASIS

 

[Indy_Guy_77]

Just remember, if you buy an intgegrally suppressed upper for your Ruger, you can't then use that suppressor on any other hosts.

For me, that's a deal breaker.

Once I get a suppressor for MY Ruger, I also plan on getting a threaded bbl for my 10/22 rifle and having the bbl on my CZ452 threaded as well.

Then I can have THREE suppressor hosts....for less money than 1 ingegrally suppressed upper.

They DO look sharp, though, I'll give you that!

-J-

 

[jongo1]

thanks guys, I guess I will just have to decide which way to go.

 

[VUPDblue]

lemme get bigcraig to post a pic of his setup. it ts a muzzle can but it mates to his upper seamlessly and looks integral.

 

[bigcraig]

Tactical Innovations Stratus suppressor mated to a Tactical Solutions Pac-lite upper.

 

[G McBride]

I struggled with the same decision and I ended up buying the Gemtech Outback II and having the barrel threaded by Gemtech. I also have a P22 and a 10/22 that host the silencer.

Bigcraig, that is a nice looking set up you have.

 

[Indy_Guy_77]

I stopped in at BG firearms yesterday afternoon... To talk suppressors. :-)

I'm quite ready to bite the proverbial bullet and start the process to get one!

And since Imitation is the most sincere form of flattery, I do believe that I'm going to put a Tac Innovations Stratus on my Tac Solutions PacLite upper on MY Ruger 22/45.

Unless, of course, the TacSol suppressors are a little less expensive. :-)

-J-

 

[bigcraig]

Most screw on .22 suppressors run around $250-$350.

There are some really expensive .22 cans out there that use monolithic baffle systems and fancy quick connect systems, but your first .22 can should be a simple design to learn the ropes, then later on you can weigh the pros and cons of a higher end .22 can.

 

[jongo1]

I stopped in at 21st century and bought me a tac 65 yesterday.now the waiting begins.i also picked up a cz 452 w/threaded barrel so i will be ready when i get the "good to go call".who knows maybe i can find a handgun setup while i wait:-)

 

[KokomoDave]

I may have posted this before but this is my current set-up.

Tact Sol w/ Outback II

P22 w/ the same Outback II and Insight taclight

S&W 622 with my Outback II

 

[knobcreeknut]

where did you get the thread adapter for your 622? I have a 452 i would like to put my can on.

 

[guffey1100]

I think you might be better off selling you ruger and buying one all ready done. you can get a MK3 in 316 Stainless for $900

 

[dunningben]

.

 

[dunningben]

where did you see this? i've seen them for 1000 and up, plus the $200 tax

I think you might be better off selling you ruger and buying one all ready done. you can get a MK3 in 316 Stainless for $900

 

[jongo1]

back to 21st already to get my handgun host.picked up a mosquito which was a tough choice over the walther p22 but a good choice either way.now all i need is the call.