FOR SALE:
SBC RACE ENGINE with roughly (50) 300ft passes... yes, that is under 3 miles!
360 cubic inches
625hp +
Built Spring 2012
All good parts!
RACE ENGINE COMPONENTS LIST
BLOCK
GM 3970010 4-BOLT MAIN BORED TO 4.060, 0.022 DECK HEIGHT
ROTATING ASSEMBLY
CRANK
GM 1182 NITRIDED FORGED STEEL CRANK 3.480 STD/STD BALANCED/POLISHED BY ZIMMERMAN BROTHERS SPEED SHOP
RODS
EAGLE “ESP” H-BEAM 6.0 INCH ARP 8740 BOLTS FLOAT-FIT WRIST PINS
PISTONS
SRP FORGED 11CC SOLID DOME 4.060 BORE 6.0 INCH ROD DOUBLE SPIRO-LOCKS
RINGS
TOTAL SEAL CONVENTIAL RING FILE FIT PLASMA-MOLY RINGS
FLEX PLATE
SFI CERTIFIED 168 TOOTH DOUBLE WELDED RING GEAR
CYLINDER HEADS
DART PRO 1 ALUMINUM 230CC INTAKE RUNNER
2.08/1.60 VALVES
HAND PORTED
FLOWED BY ZIMMERMAN BROTHERS SPEED SHOP
(ALL NUMBERS WERE OBTAINED PRIOR TO A COMPETITION VALVE JOB)
INTAKE FLOWS – 319+ @ .800 LIFT
EXHAUST FLOWS – 243+ @.800 LIFT
COMPETITION 5 ANGLE VALVE JOB
FLAT MILLED .030
62.5CC COMBUSTION CHAMBER
VALVE TRAIN
TIMING COVER
STOCK GM TYPE WITH Y PATTERN TO CLEAR CAM BUTTON
TIMING CHAIN
CLOYES QUICK ADJUST TRUE DOUBLE ROLLER. 12* TOTAL TIMING ADJUSTMENT
CAM BUTTON
LUNATI ROLLER
CAMSHAFT
COMP CAMS CUSTOM GRIND BILLET SOLID ROLLER 4/7 SWAP
5000-7800 RPM RANGE
REQUIRES BRONZE DISTRIBUTOR GEAR
.660 LIFT INT/EXH WITH A 1.50 RATIO ROCKER / .704 LIFT WITH CURRENT 1.60 RATIO ROCKER ARMS
280/292 DURATION @ .050 LIFT VALVE LASH - .026-.028
LIFTERS
PBM SOLID ROLLER HORIZONTAL RETAINER W/SPRING
PUSHRODS
PBM 5/16 .080 WALL CROMOLY HARDENED +.100 LONG (7.900)
VALVE SPRINGS
K-MOTION K950 INSTALLED @ 1.95
VALVE SPRING RETAINERS
PBM TITANIUM 1.550 +.100 TALL
ROCKER ARMS
TRICK FLOW SPECIATIES 1.60 RATIO 7/16 STUD ALUMINUM BODY FULL ROLLER
STUD GIRDLE
PBM ALUMINUM STANDARD SPACING CONFIGURATION 7/16 POLY LOCKS
LASH CAPS
COMP CAMS 5/16 .030 THICK
VALVE COVERS
EDELBROCK ELITE SERIES TALL
INTAKE
EDELBROCK SUPER VICTOR
4150 BASE
GASKET MATCHED TO FEL-PRO 1206
MILLED .030 TO MATCH HEADS
OIL SYSTEM
OIL PAN
HAMBURGER'S 1088 HAS WINDAGE TRAY, BAFFLES AND CRANK SCRAPER 7QT
OIL PUMP
MELLING 32A– HOLDS 70PSI AT IDLE COLD/35-40PSI WARM (1500 RPM IDLE DUE TO CAM PROFILE) WITH 20W50 TJ RACING LUBRICANTS FULL SYNTHETIC OIL. WELDED AND BOLTED PICK-UP TUBE DESIGNED FOR OIL PAN
OIL PUMP DRIVE
ARP HARDENED DRIVE SHAFT
BEARINGS
CLEVITE 77 H-SERIES STD/STD RODS AND MAINS
OIL FILTER USED
WIX RACING 51061R
IGNITION
MSD 85551 PRO BILLET DISTRIBUTOR (LOCKED) BRONZE GEAR INSTALLED
MSD DIGITAL 6AL WITH BUILT IN REV LIMITER
MSD HIGH VIBRATION COIL
MSD 8.5MM SUPER CONDUCTOR WIRES / CUSTOM MADE LENTGH FOR 4/7 SWAP
WATER PUMP
CAST IRON WATER PUMP
GROUND TO FIT
MR. GASKET ELECTRIC WATER PUMP KIT
Asking $7500
I will also separate short block and heads.
I also have a Ford 9" rear end for sale:
Big bearing housing
31 spline 5x5.5 bolt pattern
4.11 gears
lightened steel spool with new bearings
small bearing hog head
28 spline pinion with new bearings
complete drum to drum
$400 OBO
Call me or text 765-561-5391
Jason
I will trade to an extent, but cash is king!
Looking for:
Complete RCBS Reloading Set
Redding 223 Comp Reloading Equipment
Redding 9mm Reloading Equipment
Quality Firearms
Other go fast items
Pics are below due to length of post
SBC RACE ENGINE with roughly (50) 300ft passes... yes, that is under 3 miles!
360 cubic inches
625hp +
Built Spring 2012
All good parts!
RACE ENGINE COMPONENTS LIST
BLOCK
GM 3970010 4-BOLT MAIN BORED TO 4.060, 0.022 DECK HEIGHT
ROTATING ASSEMBLY
CRANK
GM 1182 NITRIDED FORGED STEEL CRANK 3.480 STD/STD BALANCED/POLISHED BY ZIMMERMAN BROTHERS SPEED SHOP
RODS
EAGLE “ESP” H-BEAM 6.0 INCH ARP 8740 BOLTS FLOAT-FIT WRIST PINS
PISTONS
SRP FORGED 11CC SOLID DOME 4.060 BORE 6.0 INCH ROD DOUBLE SPIRO-LOCKS
RINGS
TOTAL SEAL CONVENTIAL RING FILE FIT PLASMA-MOLY RINGS
FLEX PLATE
SFI CERTIFIED 168 TOOTH DOUBLE WELDED RING GEAR
CYLINDER HEADS
DART PRO 1 ALUMINUM 230CC INTAKE RUNNER
2.08/1.60 VALVES
HAND PORTED
FLOWED BY ZIMMERMAN BROTHERS SPEED SHOP
(ALL NUMBERS WERE OBTAINED PRIOR TO A COMPETITION VALVE JOB)
INTAKE FLOWS – 319+ @ .800 LIFT
EXHAUST FLOWS – 243+ @.800 LIFT
COMPETITION 5 ANGLE VALVE JOB
FLAT MILLED .030
62.5CC COMBUSTION CHAMBER
VALVE TRAIN
TIMING COVER
STOCK GM TYPE WITH Y PATTERN TO CLEAR CAM BUTTON
TIMING CHAIN
CLOYES QUICK ADJUST TRUE DOUBLE ROLLER. 12* TOTAL TIMING ADJUSTMENT
CAM BUTTON
LUNATI ROLLER
CAMSHAFT
COMP CAMS CUSTOM GRIND BILLET SOLID ROLLER 4/7 SWAP
5000-7800 RPM RANGE
REQUIRES BRONZE DISTRIBUTOR GEAR
.660 LIFT INT/EXH WITH A 1.50 RATIO ROCKER / .704 LIFT WITH CURRENT 1.60 RATIO ROCKER ARMS
280/292 DURATION @ .050 LIFT VALVE LASH - .026-.028
LIFTERS
PBM SOLID ROLLER HORIZONTAL RETAINER W/SPRING
PUSHRODS
PBM 5/16 .080 WALL CROMOLY HARDENED +.100 LONG (7.900)
VALVE SPRINGS
K-MOTION K950 INSTALLED @ 1.95
VALVE SPRING RETAINERS
PBM TITANIUM 1.550 +.100 TALL
ROCKER ARMS
TRICK FLOW SPECIATIES 1.60 RATIO 7/16 STUD ALUMINUM BODY FULL ROLLER
STUD GIRDLE
PBM ALUMINUM STANDARD SPACING CONFIGURATION 7/16 POLY LOCKS
LASH CAPS
COMP CAMS 5/16 .030 THICK
VALVE COVERS
EDELBROCK ELITE SERIES TALL
INTAKE
EDELBROCK SUPER VICTOR
4150 BASE
GASKET MATCHED TO FEL-PRO 1206
MILLED .030 TO MATCH HEADS
OIL SYSTEM
OIL PAN
HAMBURGER'S 1088 HAS WINDAGE TRAY, BAFFLES AND CRANK SCRAPER 7QT
OIL PUMP
MELLING 32A– HOLDS 70PSI AT IDLE COLD/35-40PSI WARM (1500 RPM IDLE DUE TO CAM PROFILE) WITH 20W50 TJ RACING LUBRICANTS FULL SYNTHETIC OIL. WELDED AND BOLTED PICK-UP TUBE DESIGNED FOR OIL PAN
OIL PUMP DRIVE
ARP HARDENED DRIVE SHAFT
BEARINGS
CLEVITE 77 H-SERIES STD/STD RODS AND MAINS
OIL FILTER USED
WIX RACING 51061R
IGNITION
MSD 85551 PRO BILLET DISTRIBUTOR (LOCKED) BRONZE GEAR INSTALLED
MSD DIGITAL 6AL WITH BUILT IN REV LIMITER
MSD HIGH VIBRATION COIL
MSD 8.5MM SUPER CONDUCTOR WIRES / CUSTOM MADE LENTGH FOR 4/7 SWAP
WATER PUMP
CAST IRON WATER PUMP
GROUND TO FIT
MR. GASKET ELECTRIC WATER PUMP KIT
Asking $7500
I will also separate short block and heads.
I also have a Ford 9" rear end for sale:
Big bearing housing
31 spline 5x5.5 bolt pattern
4.11 gears
lightened steel spool with new bearings
small bearing hog head
28 spline pinion with new bearings
complete drum to drum
$400 OBO
Call me or text 765-561-5391
Jason
I will trade to an extent, but cash is king!
Looking for:
Complete RCBS Reloading Set
Redding 223 Comp Reloading Equipment
Redding 9mm Reloading Equipment
Quality Firearms
Other go fast items
Pics are below due to length of post
Last edited:
